Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
- Control systems of the engine
   Specifications
   System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions
   Removal and PCM/ECM installation
   Check of serviceability of a state and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a state and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a state and replacement of the sensor of temperature of the soaked-up air (IAT)
   Check of serviceability of a state and replacement of the sensor of temperature of cooling liquid of the engine (EST)
   Check of serviceability of a state and replacement of the sensor of VMT/provision of a cranked shaft / situation of pistons in cylinders of the engine (TDC/CKP/CYP)
   Check of serviceability of a state and replacement of the sensor of fluctuations of a bent shaft (CKF)
   Check of serviceability of a state and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a state and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a state and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a state and replacement of the sensor of a detonation
   Check of serviceability of a state and replacement of the sensor of speed of the movement of the car (VSS)
   System of stabilization of turns of idling - the general information, check of a state and replacement of the IAC valve
   Check of serviceability of a state and replacement of the thermosensitive valve of turns of bystry idling (FIT)
   System of a perepuskaniye of the soaked-up air - the general information, check of a state and replacement of a diaphragm of the IAB valve
   System of the operated ventilation of a case (PCV)
   System of recirculation of the fulfilled gases (EGR) - the general information, check of a state and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a state and replacement of components
   The catalytic converter - the general information, check of a state and replacement
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


5642a57a



Check of serviceability of a state and replacement of the thermosensitive valve of turns of bystry idling (FIT)

The FIT valve is installed on some models of cars and is used for increase in turns of idling due to supply of additional air in the inlet pipeline in the course of warming up of the engine.

Check

 PERFORMANCE ORDER

1. At the time of the beginning of check the engine has to be in a cold state. Disconnect from the throttle case an air supply sleeve (see the Head of the Power supply system and release).

2. Start the engine on single turns. Push a finger in the case of a throttle and press it to the union connected to the FIT valve (see an accompanying illustration). Depression has to be felt.

3. Warm up the engine up to the normal working temperature and repeat check. This time depression has to be absent. Presence of tension means incomplete closing of the valve which reason the low level of cooling liquid or presence of air traffic jams in the highway of the cooling system can be – check, execute necessary adjustments.
4. If the level of liquid is normal, and air is completely removed from system, replace the FIT valve.

Replacement

Before starting implementation of the procedure, wait for full cooling of the engine.


 PERFORMANCE ORDER

1. Disconnect a hose from the valve, then turn out fixing bolts (see an illustration above). remove the valve together with sealing rings. At once to a zakuporta the open end of a hose for the purpose of minimization of losses of cooling liquid.
2. Install the valve on the regular place (do not forget to replace sealing rings), screw fixing bolts and tighten them with the required effort. In case of need replace a collar of fastening of a hose.
8 Check the level of cooling liquid, in case of need make adjustment (see the Head Routine maintenance).