Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
- Engine
- Repair of the engine without extraction from the car - the Civic model
General information
Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
Removal and installation of a cover of a head of cylinders
Removal and installation of the inlet pipeline
Removal and installation of a final collector
The VTEC systems - the general information and check of a condition of components
Removal, check of a state and installation of assembly of yokes
Replacement of valvate springs with plates and maslootrazhatelny caps
Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive
Replacement of a forward epiploon of a bent shaft
Removal, check of a state and installation of the camshaft
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a state and installation of the oil pump
Removal and installation of a flywheel / driving disk
Replacement of a back epiploon of a bent shaft
Check of a state and replacement of support of a suspension bracket of the power unit
+ Repair of the engine without extraction from the car - the Integra model
+ General and capital repairs of the engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive Removal
|
|
1. Disconnect a negative wire from the battery.
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! |
2. Prop up back wheels antiretractable boots and strongly cock the parking brake.
3. Weaken nuts of fastening of forward wheels, then a front of the car and establish to a poddomkratta it on props (see the Head Routine maintenance).
4. Remove forward wheels and protection of a case of the engine.
5. Prop up a jack the power unit (for the purpose of distribution of loading lay wooden whetstone between a head of a jack and the pallet of a case of the engine).
6. Remove an arm of the top support of the engine (see Check of a state and replacement of support of a suspension bracket of the power unit).
7. Turn out spark plugs and take off driving belts (see. Routine maintenance).
8. Otboltite the steering pump also shift it aside, without disuniting hydraulic lines (see the Head Podvesk and steering).
9. Take the probe of measurement of motive oil.
10. Bring the piston of the first cylinder into the provision of VMT of the end of a step of compression (see Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)).
|
|
The bent shaft should be turned only in the normal direction (counterclockwise) – failure to follow this requirement will lead to violation of adjustments of a gas-distributing belt. |
|
|
11. Remove the top cover of a belt of the GRM drive (see an accompanying illustration). |
12. Shoot from a forward part of the engine an intermediate video with an arm.
|
|
13. By means of a chain or tape key block a pulley of a kolenchatogoval from a provorachivaniye, then a face key weaken a bolt of fastening of a pulley (see an accompanying illustration). |
14. Remove a pulley from a pin of a bent shaft.
15. Pick up the directing phone of the measuring probe from a forward part of the engine.
16. Remove the lower cover of a gas-distributing belt.
|
|
17. If the old belt is in good repair and will be established into place, mark with chalk or white paint the direction of its rotation and situation concerning cogwheels of shaft (see an accompanying illustration). |
|
|
18. Weaken a bolt of fastening of a natyazhitel of a gas-distributing belt (see an accompanying illustration). Having wrung out a natyazhitel, weaken a belt, then again tighten a bolt. Remove the sensor of fluctuations of a bent shaft (see in the same place), then throw off a belt from cogwheels. If removal of a belt is made for the purpose of performance of replacement of an epiploon of a bent shaft, throw off from a pin of the last a cogwheel and an internal guide of a belt (see Replacement of a forward epiploon of a bent shaft). |
19. If there is a need for removal of the camshaft, or replacement of its epiploon, pass the big screw-driver through an opening in a shaft cogwheel for the purpose of blocking it from a provorachivaniye, then a face key weaken a fixing bolt and remove a wheel. Take a segment spline from a camshaft pin. |
|
Check
|
|
|
|
1. Manually check freedom of rotation of a roller of a natyazhitel, then pull it here and there, checking for existence of a side play in the bearing (see an accompanying illustration). The defective roller is subject to replacement. |
|
|
2. Attentively examine a gas-distributing belt on both sides, checking it for existence of signs of wear (especially persistent walls of teeths), cracks, cuts, attritions and traces of oiling (see an accompanying illustration). The defective belt is subject to obligatory replacement. |
|
|
If only the run of the engine is not really small, replacement of a belt is recommended to be made regardless of its state. Do not install an old belt on the engine at all, for all hundred percent being not sure of serviceability of its state. |
|
|
Installation
|
|
1. If removed, establish into place cogwheels of shaft (do not forget about a segment spline of a wheel of the camshaft and an internal guide of a belt on a bent shaft). Tighten a bolt of fastening of a cogwheel of the camshaft with the required effort (see Specifications).
|
|
2. Before installation of a belt make sure that the cogwheel of the camshaft is established by a tag in the form of a point, or letters of "UP" up. Two adjusting tags have to appear in the plane of a surface of a head of cylinders (see an accompanying illustration). |
|
|
3. Temporarily establish into place and fix by a bolt a pulley of a bent shaft, then turn a shaft (if he was hit) so that the adjusting tag on its cogwheel was combined with the response index on the case of the oil pump (see an accompanying illustration). |
|
|
4. Densely put on a belt a cogwheel of a bent shaft, then carry out it under a roller of a natyazhitel and around cogwheels of the water pump and camshaft (see an accompanying illustration). |
5. Weaken a bolt of a natyazhitel, having provided a belt tension, then temporarily tighten a bolt.
6. Accurately turn a bent shaft six times in the direction counterclockwise, then make sure of correctness of an arrangement of adjusting tags of a cogwheel of the camshaft. If the bent shaft is turned with breakthroughs, or got jammed, it is not necessary to apply force as it can lead to damage of valves at blow them about the bottoms of pistons (if adjustment is brought down). Take off a belt and repeat the procedure, paying special attention to combination of adjusting tags.
7. For adjustment of effort of a tension of a belt weaken half way (180 °) a bolt of a natyazhitel and turn a bent shaft in the direction counterclockwise on three teeth for the provision of VMT. Now tighten a bolt with the required effort.
8. Establish into place all components which were removed in the course of dismantle.
9. Adjust efforts of a tension of driving belts (see the Head Routine maintenance).
10. Start the engine and check serviceability of its functioning. |
|
|
|
