Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
- Engine
- Repair of the engine without extraction from the car - the Civic model
General information
Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
Removal and installation of a cover of a head of cylinders
Removal and installation of the inlet pipeline
Removal and installation of a final collector
The VTEC systems - the general information and check of a condition of components
Removal, check of a state and installation of assembly of yokes
Replacement of valvate springs with plates and maslootrazhatelny caps
Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive
Replacement of a forward epiploon of a bent shaft
Removal, check of a state and installation of the camshaft
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a state and installation of the oil pump
Removal and installation of a flywheel / driving disk
Replacement of a back epiploon of a bent shaft
Check of a state and replacement of support of a suspension bracket of the power unit
+ Repair of the engine without extraction from the car - the Integra model
+ General and capital repairs of the engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of a cover of a head of cylinders Removal
|
|
1. Disconnect a negative wire from the battery.
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! |
2. Uncover with heads cylinders of the ignition distributor with the wires connected to it by VV. Disconnect wires from the plugs on a head of cylinders and its cover (see the Head Routine maintenance). Do not forget to mark wires in order to avoid violation of an order of ignition at assembly.
3. Mark and disconnect all procedures of a wire impeding the implementation and hoses from the case of a throttle and a cover of a head of cylinders.
4. Carefully wipe a cover in order to avoid hit of garbage in a head cylinders/assembly of the valvate mechanism.
5. Turn out bolts of fastening of a cover of a head of cylinders – act as it should be, the return specified in a picture (see an illustration below).
6. Accurately uncover together with sealing laying. If laying of a podlipl to the interfaced head surface, tap a cover the hammer with soft brisk for the purpose of destruction of a layer of sealant. Do not make at all attempts to separate a cover by a poddevaniye its lever entered between the interfaced surfaces. |
|
Installation
|
|
1. Separate old laying, then carefully smooth out the interfaced surfaces of a head of cylinders and its cover. Having scratched out traces of old sealant and fragments of laying, wipe surfaces with the rags moistened in acetone.
2. Impose a little RTV sealant on corners where the interfaced surface of a head adjoins to assembly of yokes (see an accompanying illustration). Wait about five minutes, waiting for the moment of the beginning of polymerization of sealant.
|
|
Make sure that the top layer of sealant slightly hardened, only after it start installation of a cover (in the conditions of the increased humidity polymerization of sealant can begin with a small delay). |
|
|
3. Fill cast laying in the flute going on cover perimeter. Put the isolating plugs through passage in a cover, having slightly greased them with solution of soap water. Lay a cover on a head, then screw fixing bolts and tighten them in that order (see an accompanying illustration) with the required effort (see Specifications). |
4. Further installation is made as it should be, the return to a removal order. Before connecting wire VV, make sure of reliability of landing of rubber sealants of spark plugs. |
|
|
|
