Honda Civic/Acura Integra

since 1994 release

Repair and operation of the car



Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
- Engine
   + Repair of the engine without extraction from the car - the Civic model
   + Repair of the engine without extraction from the car - the Integra model
   - General and capital repairs of the engine
      General information
      Check of pressure of oil
      Check of compression pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal from the car of the power unit - preparation and precautionary measures
      Removal and installation of the engine
      Alternative versions of schemes of recovery repair of the engine
      Order of dismantling of the engine by preparation it to capital repairs
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal of conrod and piston assemblies
      Removal of a bent shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of conrod and piston group
      Check of a condition of a bent shaft
      Check of a state and selection of inserts of radical and conrod bearings of a bent shaft
      Engine assembly order
      Installation of piston rings
      Installation of a bent shaft and check of working gaps of radical bearings
      Replacement of a back epiploon of a bent shaft
      Installation of conrod and piston assemblies and check of size of working gaps in conrod bearings of a bent shaft
      Trial start and running in of the engine after capital repairs
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


5642a57a



Replacement of a back epiploon of a bent shaft

 PERFORMANCE ORDER

Before pribolchivat to the engine the holder with the new epiploon established in it, establish into place a bent shaft and covers of radical bearings.


1. Measure the regular depth of landing of an old epiploon in the holder's nest, then lay the holder's plate edges on pair of wooden blocks of equal height and by means of a suitable drift and the hammer beat out an old epiploon from the nest (see an accompanying illustration). Try not to damage nest walls.

2. Carefully wipe the holder, then grease the outer edge of a new epiploon with pure motive oil. The epiploon has to be put in a nest strictly perpendicularly therefore it is not recommended to make clogging it in the holder the hammer. In the absence of access to a press the epiploon can be filled in a nest by means of a big vice with soft sponges – at the same time the holder with an epiploon have to be clamped between two flat wooden whetstones providing uniform distribution of loading on all area of a face surface of an epiploon. Use of the hammer is as a last resort allowed, however the zastukivaniye has to be made through flat wooden whetstone (see an accompanying illustration). Act slowly, watching that there was no distortion.

3. By means of the probe of lezviyny type measure a gap between an epiploon and the holder. The gap has to have equal size on all perimeter of the holder and not exceed the limit of the range of 0.51÷0.76 mm.

4. Apply a thin film of RTV sealant on all edge of the holder.
5. Before putting on assembly of the holder with an epiploon a pin of a bent shaft, grease epiploon sponges with universal lubricant. Do not forget to replace sealing laying of the holder.

Before installation both surfaces of laying should be greased with RTV sealant also.


6. Having put the holder closely to the block, by hand acquire bolts of its fastening, make sure of correctness of installation of the holder, then tighten bolts with the required effort (see Specifications to Parts Repair of the engine without extraction from the car - the Civic models and Repair of the engine without extraction from the car - the Integra model of the present Chapter). Trim the edge of laying aflush with the interfaced surface of the pallet of a case (try not to scratch the last).