Honda Tsivik
+ Cars of the Honda Civic and Acura Integra brand
+ Maintenance instruction
+ Routine maintenance
- Engine
+ Repair of the engine without extraction from the car - the Civic model
+ Repair of the engine without extraction from the car - the Integra model
- General and capital repairs of the engine
General information
Check of pressure of oil
Check of compression pressure in cylinders
Diagnostics of a condition of the engine with use of the vacuum gage
Removal from the car of the power unit - preparation and precautionary measures
Removal and installation of the engine
Alternative versions of schemes of recovery repair of the engine
Order of dismantling of the engine by preparation it to capital repairs
Dismantling of a head of cylinders
Cleaning and check of a condition of a head of cylinders
Service of valves
Assembly of a head of cylinders
Removal of conrod and piston assemblies
Removal of a bent shaft
Cleaning of the block of the engine
Check of a condition of the block of the engine
Honingovaniye of mirrors of cylinders
Check of a condition of components of conrod and piston group
Check of a condition of a bent shaft
Check of a state and selection of inserts of radical and conrod bearings of a bent shaft
Engine assembly order
Installation of piston rings
Installation of a bent shaft and check of working gaps of radical bearings
Replacement of a back epiploon of a bent shaft
Installation of conrod and piston assemblies and check of size of working gaps in conrod bearings of a bent shaft
Trial start and running in of the engine after capital repairs
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of the engine
|
|
It is worth to remember that gasoline is flammable liquid in the highest measure – during the work with components of a power supply system observe all taken measures of fire safety. You do not smoke and do not approach the venue of works with naked flame or the carrying unprotected by the lamp shade. You do not make service of system in the room equipped with the heating devices using natural gas and equipped with a control torch (such as vodogre and dryers for clothes). Do not forget that gasoline is among the cancerogenic substances promoting development of cancer – try not to allow hits of fuel on open parts of the body – use protective rubber gloves, at casual unforeseen contact carefully wash out hands warm water with soap. Immediately collect the spilled fuel and do not put the rags impregnated with fuel and lubricants near sources of naked flame. Remember that the power supply system of the models equipped with injection of fuel constantly is under pressure. Before starting a detachment of fuel lines, dump residual pressure in system (for more details see the Head of the Power supply system and release). At service of components of a power supply system put on goggles. Constantly hold near at hand the class B fire extinguisher! |
The path of the air conditioning system also constantly is under pressure, and therefore before a rassoyedineniye of refrigerator lines it is necessary to make a system discharge in the conditions of a specialized workshop.
|
|
On the considered models the engine is removed assembled with transmission. Before getting to work attentively get acquainted with materials of the present Section. It will be useful to impregnate with beforehand getting oil such hardly given fixture as nuts/bolts of fastening of a final collector, support of the power unit, etc. |
Removal
|
|
| 1. Dump pressure in a power supply system (see the Head of the Power supply system and release).
2. Disconnect a negative wire from the battery. Disconnect also positive wire, then release fixture of opposite tips of both wires and take the last of a motive compartment. on the Civic models remove the battery and take from a motive compartment its adjusting pallet (see the Head Elektrooborudovaniye of the engine).
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! |
3. Cover wings and an airreflector under a car windshield special protective covers, or just old blankets. As it is possible open a cowl (Civic models) more widely, or remove it absolutely (Integra models) (see the Head Kuzov).
|
|
4. On the Integra models remove an expansion bar of a motive compartment (see an accompanying illustration). |
5. Remove assembly of the air cleaner with an air inlet sleeve (see the Head of the Power supply system and release).
|
|
6a. Accurately mark and disconnect from the engine all vacuum lines, hoses of system of decrease in toxicity of the fulfilled gases, sockets, an electrical wiring, the tire of grounding and fuel pipes (see accompanying illustrations). On the Civic models disconnect an electrical wiring from the module of management of the power (RSM) in interior of the car (see the Head of the Control system of the engine), then take rubber plugs through passage from a back partition of a motive compartment and push the main braid of an electrical wiring through a partition. It is the best of all to make marking of an electrical wiring, lines and hoses by means of an adhesive tape. It will also be useful to make the scheme of laying of communications, or to execute a series of pictures. |
|
|
6b. On the Integra models the socket of the main braid is located at the left in a motive compartment. |
7. Having marked, disconnect all hoses of the cooling system from the engine.
8. Remove a broad tank, the cooling system fan with a casing and a radiator (see the Head of the Cooling system and heating).
9. Take off a driving belt (i) and a tension roller (if that is provided) (see the Head Routine maintenance).
10. Disconnect the fuel lines going from the engine to the chassis (see the Head of the Power supply system and release). Zakuporte the open ends of lines and unions in order to avoid hit of dirt in a power supply system.
11. Disconnect from the engine draft of an accelerator (see the Head of the Power supply system and release), and also a cable of the drive and the actuation mechanism of a tempostat (at the corresponding complete set of the car).
12. Otboltite the steering pump also shift it aside, without disconnecting hydraulic lines (see the Head Podvesk and steering). Track that the pump was fixed strictly vertically.
13. On the models equipped with the conditioner of air (K/V), an otboltita also shift the compressor aside – do not disunite refrigerator lines (see the Head of the Cooling system and heating).
|
|
Reliably fix the removed compressor by a wire, without allowing it to hang on hoses. |
14. Otboltite the generator also shift it together with a basic level aside (see the Head Elektrooborudovaniye of the engine).
15. The car also establish to Poddomkratta it on props. Empty the cooling system (see the Head Routine maintenance).
16. Merge motive oil and remove an oil filter (see the Head Routine maintenance).
17. Remove a starter (see the Head Elektrooborudovaniye of the engine).
18. Remove protection of a case (see the Head Kuzov).
19. On models with AT disconnect a cable of the drive of a butterfly valve from a transmission case. Also disconnect from transmission all electrical wiring and a cable of switching (see 4-staged and stepless automatic transmissions (ат and cvt)).
20. On models with AT disconnect also from transmission of the line of cooling of ATF.
21. Remove a pulley of a bent shaft and screw into place a bolt.
22. Disconnect from the engine a reception pipe of system of production of the fulfilled gases (see the Head of the Power supply system and release).
23. Prop up transmission a cart jack. Do not forget to lay between a head of a jack and a case of transmission wooden whetstone for distribution of loading.
|
|
24. Connect to the engine lifting slings or chains (see an accompanying illustration). |
25. Move the winch into position (strictly over the engine) and fill a rigging, without raising the engine so far.
|
|
Try not to thrust hands under the power unit withheld in hover! |
26. Remove power shafts (see the Head Stsepleniye and power shafts).
27. On models with RKPP you otboltit the executive cylinder of coupling and shift it aside, without disconnecting hydraulic lines (see the Head Stsepleniye and power shafts). Disconnect drafts of gear shifting (see a 5-staged manual box of gear shifting).
28. Turn out bolts of fastening of support of the power unit to chassis elements (see Parts Repair of the engine without extraction from the car - the Civic models or Repair of the engine without extraction from the car - the Integra model of the present Chapter).
29. Make sure that anything else does not connect the power unit to the car. In case of need make necessary detachments, previously having marked the forgotten communications.
30. Slowly lift the engine, accurately releasing its support. At the same time raise a jack transmission. Having made sure of lack of hindrances, take assembly of the power unit from a motive compartment.
31. Carefully omit assembly of the power unit on a floor of a garage and prop up it wooden blocks. If necessary remove a flywheel / a driving disk and install the engine on the assembly stand.
32. Separate transmission from the engine (see the Head Korobk of gear shifting). |
|
Installation
|
|
1. Check a condition of support of the power unit. Replace defective components.
2. On models with RKPP check a condition of components of coupling (it will be correct to replace all assembly). Establish coupling (see the Head Stsepleniye and power shafts) and grease with high-temperature lubricant of a vent of a main shaft of the transmission.
3. Accurately connect transmission to the engine.
|
|
In order to avoid damage of the main components, do not use fixing bolts for alignment of transmission and the engine from each other at all! On models with AT extra care should be shown at installation of the converter of rotation (strictly follow the instructions stated in 4-staged and stepless automatic transmissions (ат and cvt)). |
4. Connect a rigging to the power unit, lift assembly and accurately bring it on the regular place to a motive compartment of the car.
5. Screw fixing bolts and strongly tighten them. You make further assembly as it should be, the return to a dismantle order.
6. Add in the engine cooling liquid and engine oil, fill transmission and system of hydrostrengthening of a wheel (see the Head Routine maintenance).
7. Start the engine and check it for serviceability of functioning and existence of signs of leaks. Switch off ignition and check levels of working liquids of the power unit. If removed (Integra models), establish into place a cowl. Make trial runs of the car.
8. On the models equipped To/in make evacuation and charging of air conditioning system in the conditions of a specialized workshop. |
|
|
|
